Look up another CVE · open CVE-2026-98530 in the interactive tracker
CVE-2026-98530
kprobes: Fix permanent hang when flushing the kprobe optimizer
Published 2026-10-18 (today) by the Linux kernel CNA. Subsystem kernel. Debian urgency: unimportant.
What to do, per Debian release
Debian's own status for CVE-2026-98530 in every release this site tracks, and what each one means in practice. Every status below is the one the Debian Security Team publishes for this CVE. source
| Release | Status | Version | What this means |
|---|---|---|---|
| Debian 12bookworm | not affected | 6.1.190-1 | Nothing to do. bookworm never shipped the vulnerable code. |
| Debian 13trixie | not affected | 6.12.113-1 | Nothing to do. trixie never shipped the vulnerable code. |
| Debian 14forky | fixed | 7.2.9-1 | Update the kernel and reboot. Fixed in 7.2.9-1. A running kernel keeps the old code until the machine restarts. |
| Debian unstablesid | fixed | 7.2.9-1 | Update the kernel and reboot. Fixed in 7.2.9-1. A running kernel keeps the old code until the machine restarts. |
The vulnerability
What the bug is
Writing 0 to /proc/sys/debug/kprobes-optimization while a kprobe is jump-optimized never returns. The writer sleeps in D state forever with kprobe_sysctl_mutex held, so any later read or write of that sysctl hangs as well. For example, with vfs_read+9 as an optimizable address in this build: # cd /sys/kernel/tracing # echo 'p:myprobe vfs_read+9' >> kprobe_events # echo 1 > events/kprobes/myprobe/enable # # wait until /sys/kernel/debug/kprobes/list shows [OPTIMIZED] # echo 0 > /proc/sys/debug/kprobes-optimization INFO: task sh:246 blocked for more than 10 seconds. Call Trace: <TASK> __schedule+0x1176/0x4f70 schedule+0xdc/0x2c0 schedule_timeout+0x17b/0x260 wait_for_completion+0x173/0x3c0 wait_for_kprobe_optimizer_locked+0xbc/0x130 proc_kprobes_optimization_handler+0x156/0x1b0 proc_sys_call_handler+0x324/0x490 vfs_write+0x52d/0xfe0 ksys_write+0xff/0x200 do_syscall_64+0x106/0x630 entry_SYSCALL_64_after_hwframe+0x77/0x7f </TASK> ... INFO: task cat:265 is blocked on a mutex likely owned by task sh:246. wait_for_kprobe_optimizer_locked() reinitializes optimizer_completion, asks the optimizer thread to flush and sleeps in wait_for_completion(). The thread drains the (un)optimizing lists, but calls complete() only if completion_done() is true, i.e. if the completion is already done, which never happens while someone waits. disarm_all_kprobes() and kprobe_trace_self_tests_init() wait the same way. Calling complete() unconditionally would not be enough: the waiter drops kprobe_mutex while it sleeps, and nothing else serializes the sysctl handler against the debugfs "enabled" file. A second flusher that still finds the lists non-empty, e.g. because a disabled probe is queued for unoptimizing, reinitializes the completion under the first: sysctl write debugfs "enabled" write unoptimize_all_kprobes() wait_for_kprobe_optimizer_locked() init_completion(c) mutex_unlock(&kprobe_mutex) wait_for_completion(c) disarm_all_kprobes() wait_for_kprobe_optimizer_locked() init_completion(c) // c->wait is reset, the first // waiter is off the queue mutex_unlock(&kprobe_mutex) wait_for_completion(c) kprobe_optimizer() complete(c) // wakes the debugfs writer only where c is &optimizer_completion. Lining up the two writes during an optimizer pass loses the sysctl writer this way. Replace the completion with a counter of optimizer passes, bumped at the end of each pass and signalled with wake_up_var_locked(), both under kprobe_mutex. A flusher samples the count and waits with wait_var_event_mutex(), which drops kprobe_mutex only while sleeping, so a new count means a whole pass ran in the meantime. Nothing is reinitialized, so several flushers can sleep in the wait at once.
Where it lives
The fix touches these files. If the subsystem is one you do not use, the practical exposure is lower, though the package is still the vulnerable one.
kernel/kprobes.c
- What this is
- KPROBESMAINTAINERS section matched on kernel/kprobes.c · linux-kernel@vger.kernel.org · Maintained
Check it on the machine
grep -w CONFIG_KPROBES /boot/config-$(uname -r)Reads the booted kernel's own configuration, on the machine and nowhere else. =y is built in, =m is a module, and an is not set line means the code is not there.
Show whether Debian builds this, per release
Debian builds this code. Every release below compiles the affected file into the kernels it ships.
- bookworm, trixie, forky, sidy
- y
- built into the kernel image on every flavour - only a patch removes it
- Build switch
- CONFIG_KPROBES
From the configuration Debian publishes for every kernel flavour it builds. It covers only the architectures Debian ships a linux-config package for, and nothing about a kernel you built yourself. Debian's own status above stays authoritative about the source package.MAINTAINERS kbuild Makefiles Debian linux-config packages
Signals
- Published
- 2026-10-18 (today)source
- CVSS
- no vector published, unrated
- Attack vector
- not published
- EPSS
- not scored
- CISA KEV
- not listedthe KEV catalogue
- Debian urgency
- unimportantsource
- Subsystem
- kernel
Upstream fixes
The versions the CNA records as introducing and fixing this, and the commit for each. source
| Introduced | Fixed in | Commit |
|---|---|---|
| 7.0 | 7.2.9 | f05a01fc7d4f |
| 7.0 | 7.3 | 5bfa9f1a9dcb |
Why the CNA scored it this way
The kernel CNA published no CVSS vector and no reasoning for CVE-2026-98530, which is why it is shown as unrated rather than given an invented score. 6,405 of the 20,413 CVEs here carry reasoning; this is not one of them.